Top 5! Amazing Mass Production Tech! Best Factory!
This video shows the making of high quality dumbbells for use in the gym The video will show some rare inside views of production This video was filmed at wavar, a leading supplier of fitness and yoga equipment in China with over 10 years of experience in the fitness industry! Let's get together Round steel, the raw material for dumbbells. Preparing to cut The cutting process is very long and requires a lot of patience to shoot Putting round steel into the machine for processing Machining the edge of a dumbbell Machining the other side Making a dumbbell handle Preparing to Solder Heat from friction welds the metals together. Let's take a closer look at friction welding. I know you want to see it again :))) Solder the other end as well Now you'll be able to work out with it :))) These dumbbells Ronnie Kuhlman would love.
We need to make the dumbbells prettier, and will wrap a layer of rubber around the outside. Pouring the rubber into the hot press machine Add the flavorings again and mix well It's the same as with the pasta :))) Finished Rubber Sheet Raw Material Cutting a rubber sheet into rubber strips Preparing to make the rubber outer layer for a dumbbell Making a mold for a rubber sleeve Putting the rubber strip into the vulcanizing machine The rubber heats up in the mold in the same way that bread expands in the oven. The initial form of the dumbbell Removing the dumbbell Grooming the dumbbells, trimming the excess rubber from the edges. Remember to subscribe to the channel so the dumbbells don't fall on your toes when you're gym :))) Thank you for your patience :)))Next up, we show how a barbell plates is made This video shows the process of making a barbell plates I try to capture as much of the barbell making process as possible.
You will see jobs that can both keep fit and make money, although it is very hard let’s get into it! The truck is full of iron sand. Iron sand has a higher iron content than iron ore. Iron Sand Transportation to Smelting Plant Adding iron sand to the silo Add Pig Iron Add Iron Sand Melt at high temperature, it will take about an hour Add flavorings to remove impurities from the iron. Fishing out the impurities It's a dangerous job, with temperatures up to 45 degrees Celsius next to the furnace. Pouring iron from the furnace into the ladle. Fishing out impurities Pouring into the Secondary Melting Furnace The iron will be heated to a temperature where it can be poured Starting Machines Automatic sand molding of barbell plates Sand mold waiting to be poured Pouring iron into a sand mold Poured sand mold needs to cool down slowly Crushed sand molds, semi-finished barbell plates The iron will be recycled.
Dumbbells were also cast. The surface of the barbell piece has a lot of impurities and needs to be shot peened. Shot blasting machine Friction collision to remove impurities from the surface of barbell pieces Shot peening of the finished barbell plates Sanding This worker is strong, and his job is to lift barbells The same job you pay to do at the gym. I bet you'd be shocked if the workers took off their clothes. Because it's a maneuver that workers repeat thousands of times a day.
Barbell plate vulcanization workshop Rubber wrapped barbell pieces weigh Both sides of the barbell piece are rubberized. Add the flavorings Heating to vulcanize rubber It's similar to baking bread. Workers' jobs are like working out at the gym Repairing the excess rubber. Now making rubber barbell plates Powder coated barbell pieces Barbell plates of all sizes Remember to subscribe to the channel or I'll replace your car's steering wheel with a barbell plate!:))) Dumbbell plates go into the powder coating machine Heat treatment after powder coating Heat treatment after powder coating, which is a long process Thanks for your patience in watching :))) The making of high quality safety shoes is shown next This video shows you the making of safyty shoes You will see the whole process of manufacturing a pair of high quality safety shoes Let's go see it. Video shot at WeFang ShuangJie safyty product Products Co., Ltd
This is the warehouse where the raw materials are stored. The shelves are stocked with whole first layer cowhides. Rolls of cowhide being carried out. Transporting hides to the processing plant Now for the layout process, where the upper fittings are projected onto the whole cowhide. The whole cowhide is scanned by the camera on the top and the optimal combination of typography is calculated. The typography is projected onto the surface of the cowhide Cowhide Cutting These components will be used to sew the upper in a moment.
All the components of the upper. Sewing the heel of the shoe Cutting on the edge to thin the edge The upper is all handmade, no machine can replace it for now. Applying glue to the lining Adding sponge to soften the heel Gluing the tongue to the upper Sewing the tongue Sewing the toe and the upper together. Sewing all the components together Let's move right on to the next craft Sewing insoles for finished uppers This is no ordinary insole. The insoles are made of DuPont's Kevlar high-performance fiber composite.
In layman's terms, it's the same material as the U.S. Army's bulletproof undershirts. Kevlar is stiffer than steel, the properties of this insole will be demonstrated in the video test session This girl works with passion. Molds of all sizes Putting molds into shoes, you can put your feet in them :)) but it can be dangerous! Installing the steel toe underneath Spraying glue and installing the toe Squeeze The glue in the toe is cured by machine heat, a long process Glueing the bottom of the upper Pulling the upper tight and shaping the toes Shaping the heel Sanding Ready for the next process, rubber injection molding of the sole. Large rubber injection molding machine Installation of shoe sole molds This set of molds is worth $6,000.
Do you know why shoes are always out of stock? Because the molds are expensive. Installing a Shoe Upper Testing the sealing properties of a mold Starting the Machine Injecting liquid rubber to make a shoe sole Injection port, rubber slowly cooled and molded Applying glue to the edges Hot air drying to allow the glue to dry quickly Plastic finished soles, removing excess rubber Heating up the upper A second injection of rubber glues the upper to the sole. Advanced one-piece injection molding of the sole The finished sole.
Removing the mold Cutting off excess rubber at the edges Don't leave, in a moment we're going to go through the complete testing process of the shoe Let's start with the flex resistance test. Simulating the flexing and bending of a walking shoe It takes a simulated person to walk 30,000 steps, which is a long time, I waited 12 hours. You don't have to wait. Flexing Resistance of Upper：no cracking before 150 000 flex cycles. Static insulation test, pouring steel balls into shoes no current flow or leakage current in excess of 1.0 mA under the application of 18 000 V at 60 HZ AC for 1 minute. Next up is the steel head impact test and insole test The shoe needs to be destroyed and dismembered.
Remove the steel head. Products are tested and certified by CSA US International for sale in Canada and the United States. Simulated test of foot protection by a steel head at 50 kg.
The Impact Resistance of safety shoes needs to withstand at least (200 ± 4) J of energy to prevent impact. Final puncture test to test the insole's puncture resistance Simulated steel nail insertion into shoe sole The average value of the force required to perforate the outsole unit shall be not less than 1100 N. No single value shall be lower than 950 N. Remember to subscribe to the channel, it's important to me, thanks :))) Thank you for your patience :)) The making of safety gloves is shown below This video shows you how safety gloves are made. Video shot in China - Qingdao Finger Safety Products Co.
Let's get together. Glove Weaving Workshop Today's production of beautiful orange nylon thread gloves Nylon thread safety gloves are very light and comfortable to wear. have very good resistance to abrasion This machine knits a glove every 2 minutes.
One machine can produce 2-3 hundred gloves a day. This is a warehouse of knitted safety gloves. Automatic Safety Glove Hanging Machine Workers need to put gloves on the mold by hand The glove is rolled upwards to the next process First the glove needs to be dipped in water The purpose of dipping the glove in water is to remove impurities from the surface of the glove and to regulate humidi Removal of excess water by high frequency vibration Safety gloves dipped in latex Synthetic latex, characterized by abrasion resistance and durability Uniform coating by high frequency vibration Uniform coating of the glove by multiple rotations Now for the acid dip. Strong acid corrodes the rubber to roughen the surface of the glove, increasing friction.
Drying The whole drying process takes 3 hours The logo is printed on the top part of the machine. I'm standing at the highest point for you, I'm a little afraid of heights. I need a like to beat the fear of heights :))) Printing complete, scroll down to send to packing area Removing the glove Remember to subscribe to the channel or the doctor will wear these gloves when he sees you :))) Feel free to purchase the products in the video, so the factory will be happy! Thank you for your patience :))) This video shows the making of a Pilates bed This video was filmed at Dezhou Deren Fitness Equipment Co., Ltd. Let's go together. The wood used by the company is from Baillie in the USA and is FSC certified.
Ready to cut Polishing Cut to bedplate size Side polishing Machine Finishing Side Perforation Screwing Cutting out the rest of the Pilates bed with the machine Sorting out the parts Here are all the parts to make the bed. White latex paint. Insertion of wooden dowels for joint fixation Assembly Installing the Bed Legs Extruding The bed frame is made.
Sanding To the Paint Shop Painting Painting and drying in the warehouse Transferred to the finished product assembly plant Ready for assembly Remember to subscribe to the channel or you'll fall out of bed and onto the floor in your sleep :))) Pilates is a popular fitness exercise in Japan and Korea. This exercise can make your girlfriend more beautiful. This is the multifunctional Pilates bed you can sleep on :))) Packing Thank you for your patience in watching :))
2024-11-17 13:14
